1.80 cu in Cross Hydraulic Motor 40MH18DACSC

Item Number: 9-7073-180

Price: $259.95
TOP
Back to top

1.80 cu in Cross Hydraulic Motor 40MH18DACSC

1.80 cu in Cross Hydraulic Motor 40MH18DACSC

item number: 9-7073-180 PRICE: $259.95 10 In Stock Regular Stock Item
Prop 65 Warning WARNING: Cancer and Reproductive Harm
www.P65Warnings.ca.gov


calculate shipping
Calculate Shipping for Item 9-7073-180
1.80 cu in Cross Hydraulic Motor 40MH18DACSC
Item Number: 9-7073-180
Price: $259.95
Estimate shipping to:
Shipping Notes:
* UPS 3-Day, 2-Day, and Next Day orders entered before 1pm (CST) Mon-Fri will be shipped the same day. Orders entered Sat or Sun will be shipped the following Monday.
  • This item is on page 79 of our current catalog

You may also consider:

Description
CROSS HIGH SPEED HYDRAULIC MOTOR

Brand new, Cross hydraulic gear motor. Model 40MH18DACSC. Pressure balanced loading plates for high efficiency. Aluminum body for good heat dissipation. Pressure lubricated Teflon impregnated sleeve bearings. Internal check valves eliminate need for case drain at shaft seal pressures under 250 PSI.

SPECIFICATIONS
  • 1.8 cu in disp
  • Max Pressure 3000 PSI
  • Max speed 3000 cont
  • 15.5 GPM for 1800 RPM
  • 20 HP at 1800 RPM, 2500 PSI
  • 700 in-lbs. torque at 2500 PSI
  • Reversible Rotation
  • SAE A 2 bolt mount
  • 5/8" dia x 1-1/4" keyed shaft
  • SAE 12 ports
  • 1/4" NPT drain port
  • 5-1/4" x 5-1/8" x 4-15/16"
  • Shpg 9 lbs
More Specs
Links To More Info On This Item
Click to view...

Instructions
Click on boxes below for more information about this product.
Dimensional DiagramMore Specs
Ask A Question
Submit a question for this product

Showing Questions of 4

Hi can I use this motor to power a former engine driven welder?. The engine was 20 HP . I need 1800 RPM for the machine to work properly. Is this the best type of motor for this application? I am planning on using an open loop system with a pressure regulator.

A: If this motor is operated at 1800 rpm at 2500 psi, with no losses calculated it would produce approximately 19.9 Hp. If a continuous 20 Hp is required the system pressure may need to be raised slightly to increase torque, and therefore horsepower.

Can I buy just the base flange that has the mounting tabs on it for these Cross motors?

A: We have two mounting L-brackets for these motors. We do not carry any of the motor pieces themselves.

If I were to use a variable speed pump driven off a gas engine, could I use this motor to power a garden tractor thought it's existing axle / reduction system (54:1)? If heat is a concern, could an oil cooler be fitted?

A: Without any other information, we cannot say. It seems reasonable as long as flow, pressure, and thermal restrictions are considered.

If took a motor, your item #9-7073-180 and coupled it to an engine to use as a pump and routed the fluid to an identical motor, with a valve, your Item #: 9-7458, will I be able to use this a variable speed unit to drive a small tractor?

A: These motors were not designed to operate in a closed loop system as you describe. Overheating and cavitation would irreparably damage the motors in short order.

Recently Viewed

You may also consider:

Email a Friend
1.80 cu in Cross Hydraulic Motor 40MH18DACSC
Item Number: 9-7073-180
Price: $259.95
Message for your friend:

I found this on the Surplus Center website, https://www.surpluscenter.com/. I thought you might be interested in seeing it for yourself. Please click on the following link to view the page:

1.80 cu in Cross Hydraulic Motor 40MH18DACSC
Additional Comments:

Please wait...
Newsletter SignUp