205cc 6.5 HP Powerpro Engine 2541-0046 w/Threaded Shaft and Electric start

Item Number: 28-1898-E

Price: $169.95
Back to top

205cc 6.5 HP Powerpro Engine 2541-0046 w/Threaded Shaft and Electric start

205cc 6.5 HP Powerpro Engine 2541-0046 w/Threaded Shaft and Electric start

item number: 28-1898-E PRICE: $169.95 23 In Stock Surplus Item
Prop 65 Warning WARNING: Cancer and Reproductive Harm

calculate shipping
Calculate Shipping for Item 28-1898-E
205cc 6.5 HP Powerpro Engine 2541-0046 w/Threaded Shaft and Electric start
Item Number: 28-1898-E
Price: $169.95
Estimate shipping to:
Shipping Notes:
* UPS 3-Day, 2-Day, and Next Day orders entered before 1pm (CST) Mon-Fri will be shipped the same day. Orders entered Sat or Sun will be shipped the following Monday.
  • This item is on page 6 of our current catalog
New, PowerPro series horizontal shaft engine. Features include overhead valves, cast iron sleeve liner, mechanical governor, dual element air filter, low-oil sensor, and electronic ignition. Manual throttle and choke, key for electric start. CARB/EPA certified for emission standards. Charging circuit to keep battery charged. Special crankshaft commonly used for centrifugal pumps.

  • Model 2541-0055
  • Power 6.5 HP
  • Bore/Stroke 2.7" x 2.1"
  • Disp. 12 cu. inch
  • Speed 3600 RPM
  • Start Electric/Recoil backup
  • Shaft Horizontal
  • Shaft 5/8" diam. x 2-5/16" w/5/8-18 thread on last 1" (no keyway)
  • Accessory Mount 4 Bolt 3-5/8" B.C.
  • Fuel Tank 3.88 qt.
  • Size 14-7/8" x 12-3/8" x 13-1/4"
  • Shpg. 46 lbs.
90 Day Surplus Center WarrantyView Warranty
Warranty Information

Products we regularly stock that are purchased directly from the manufacturer are covered by that manufacturers warranty.

We warrant all other products, only to the original purchaser, to be free from defects in materials and workmanship for a period of 90 days from date of shipment.

Because we have no assurance of the purposes for which any of the items herein will or may be used, no warranty is given as to the fitness of the item for any particular purpose. You have the responsibility for determining the suitability of items herein for your particular use. We shall not be liable for incidental or consequential damages.

NOTE! Warranties do not cover bent hydraulic cylinder shafts.

We shall, at our option, repair or replace any items deemed by us to be defective under this warranty. Items returned by the purchaser for warranty adjustment must be handled as stated in our return policy. Proof of, and date of purchase will be required.

Remedies under this warranty shall be limited to the original purchase price of the claimed defective item. (Some states do not allow limitations on implied warranties, incidental or consequential damages, thus, some of the limitations or exclusions referred to above may not apply to you.)

In no event shall we be liable for any damages, or warrant any of our products which are made defective as a result of damage in shipment, user's abuse, neglect or improper operation.

Ask A Question
Submit a question for this product

Showing Questions of 9

Where can I find a parts breakdown of this engine?

A: There is a parts manual that comes with this engine.

Is this engine a copy of a Honda engine ofter referred to as a Made in China Honda engine? If so others have had success using it to replace Tecumseh engines on TroyBilt tillers.

A: These engines are made in China, and have licensed use of the trade dress characteristics commonly associated with Honda engines. Please be aware that the shaft on these engines is of a different size, is threaded for a portion, and is not keyed; as such it will not be immediately compatible with applications which use the standard 3/4" smooth keyed shaft common to this size engine.

Would this engine be a direct replacement for a Tecumseh 6.5 HP H60 or HH60 engine which is on a TroyBilt Horse Tiller?

A: We have no cross reference information to confirm that it will fit and operate in the same fashion. These engines were originally intended for water pumps in which the impeller threaded onto the engine shaft.

What is the thread diameter and pitch of the bolt holes for the pump mount?

A: The bolt holes are threaded 5/16"-24.

Would this be a good choice to be mated to a 11GPM log spliter pump? I need to re-motor & pump my very old home made log splitter? Any suggestions would be appreciated.

A: This engine has a threaded shaft that was designed specifically for use with centrifugal water pumps, and it may be difficult to make work in any other application without some modification to either the shaft or any coupler which would need to join the shafts.

Is the listed shaft diameter correct at 5/8 inch.

A: Yes. This engine has a non-standard shaft that was meant for mating to a centrifugal pump impeller.

would this work on a go cart with a chain cluch

A: If the clutch is the correct bore size and length to fit on this shaft it could be possible. Most clutches will not work, however.

What is rotation looking at it from shaft end? This engine does not have a keyway, do you have a v-belt pulley that would not spin?

A: The rotation is looking at the working end of the crankshaft. By using one of the interchangeable H Bushing type pulleys they grab very tightly to the shaft even without a keyway

Is the electric start 12 vdc?

A: Yes it is 12 Volt DC.

Recently Viewed
Email a Friend
205cc 6.5 HP Powerpro Engine 2541-0046 w/Threaded Shaft and Electric start
Item Number: 28-1898-E
Price: $169.95
Message for your friend:

I found this on the Surplus Center website, https://www.surpluscenter.com/. I thought you might be interested in seeing it for yourself. Please click on the following link to view the page:

205cc 6.5 HP Powerpro Engine 2541-0046 w/Threaded Shaft and Electric start
Additional Comments:

Please wait...
Newsletter SignUp