6.5 HP 205cc Powerpro Engine 2541-0046 w/Threaded Shaft

Item Number: 28-1898

Price: $159.95
Back to top

6.5 HP 205cc Powerpro Engine 2541-0046 w/Threaded Shaft

6.5 HP 205cc Powerpro Engine 2541-0046 w/Threaded Shaft

item number: 28-1898 PRICE: $159.95 20 In Stock Surplus Item

Available for curbside pickup in our Lincoln, NE location
calculate shipping
Calculate Shipping for Item 28-1898
6.5 HP 205cc Powerpro Engine 2541-0046 w/Threaded Shaft
Item Number: 28-1898
Price: $159.95
Estimate shipping to:
Shipping Notes:
* UPS 3-Day, 2-Day, and Next Day orders entered before 1pm (CST) Mon-Fri will be shipped the same day. Orders entered Sat or Sun will be shipped the following Monday.
  • This item is on page 6 of our current catalog
New, PowerPro series horizontal shaft engine. Features include overhead valves, cast iron sleeve liner, mechanical governor, dual element air filter, low-oil sensor, and electronic ignition. CARB/EPA certified for emission standards. Special crankshaft commonly used for centrifugal pumps.

  • Model 2541-0046
  • Power 6.5 HP
  • Bore/Stroke 2.7" x 2.1"
  • Disp. 12 cu. inch
  • Speed 3600 RPM
  • Start Recoil
  • Shaft Horizontal
  • Shaft 5/8" diam. x 2-5/16" w/5/8-18 thread on last 1" (no keyway)
  • Accessory Mount 4 Bolt 3-5/8" B.C.
  • Fuel Tank 3.88 qt.
  • Size 14-7/8" x 12-3/8" x 13-1/4"
  • Shpg. 46 lbs.

Prop 65 Warning WARNING: Cancer and Reproductive Harm

90 Day Surplus Center WarrantyView Warranty
Warranty Information

Products we regularly stock that are purchased directly from the manufacturer are covered by that manufacturers warranty.

We warrant all other products, only to the original purchaser, to be free from defects in materials and workmanship for a period of 90 days from date of shipment.

Because we have no assurance of the purposes for which any of the items herein will or may be used, no warranty is given as to the fitness of the item for any particular purpose. You have the responsibility for determining the suitability of items herein for your particular use. We shall not be liable for incidental or consequential damages.

NOTE! Warranties do not cover bent hydraulic cylinder shafts.

We shall, at our option, repair or replace any items deemed by us to be defective under this warranty. Items returned by the purchaser for warranty adjustment must be handled as stated in our return policy. Proof of, and date of purchase will be required.

Remedies under this warranty shall be limited to the original purchase price of the claimed defective item. (Some states do not allow limitations on implied warranties, incidental or consequential damages, thus, some of the limitations or exclusions referred to above may not apply to you.)

In no event shall we be liable for any damages, or warrant any of our products which are made defective as a result of damage in shipment, user's abuse, neglect or improper operation.

Ask A Question
Submit a question for this product

Showing Questions of 7

Wich way does the shaft rotate?

A: The shaft turns CCW facing the shaft.

Will this replace a Honda GX160 with threaded shaft on a honda high pressure water pump?

A: We have no information on your water pump and are unable to tell if it can be replaced with our engine.

I want to mount a centrifical clutch for snow machine do you have a clutch available for it with a sprocket?

A: While we do carry chain-type centrifugal clutches for 5/8" bore, but this engine shaft is not keyed to be compatible with them. The key is integral to the clutch and can't be removed.

Does this engine recommend/require different jets in the carb for ops above 8000 ft?

A: While the manufacturer does say that operation at over 5000 ft will result in the need for modifications for the carburetor, they do not mention what those are and state that the local servicing dealer should perform the specific modifications needed. They also mention that even with the proper modifications to the carburetor, there will be a performance drop in output Hp of approximately 3.5% per 1000 ft increase in altitude.

Is the accessory mount mentioned on this engine (3-5/8) located on the shaft side of the engine?

A: Yes. That is the 4-hole mount arranged around the crankshaft.

How do you adjust the carb on a 6.5 hp motor

A: There is a Phillips head screw for idle adjustment on the carburetor. Start the engine and warm it up. Adjust the throttle to low; adjust the idle speed as necessary. The manufacturer recommendation is 1,400 rpm (+/- 150).

Are these engines manufactured by Lian Li?

A: No manufacturer information is present on the units.

Recently Viewed
Email a Friend
6.5 HP 205cc Powerpro Engine 2541-0046 w/Threaded Shaft
Item Number: 28-1898
Price: $159.95
Message for your friend:

I found this on the Surplus Center website, https://www.surpluscenter.com/. I thought you might be interested in seeing it for yourself. Please click on the following link to view the page:

6.5 HP 205cc Powerpro Engine 2541-0046 w/Threaded Shaft
Additional Comments:

Please wait...
Newsletter SignUp