7.63 cu in PTO Drive Motor BMSY125E2SLS

Item Number: 9-7368-125

Price: $307.35
TOP
Back to top

7.63 cu in PTO Drive Motor BMSY125E2SLS

7.63 cu in PTO Drive Motor BMSY125E2SLS

item number: 9-7368-125 PRICE: $307.35 Out of Stock - More on Order Regular Stock Item


calculate shipping
Calculate Shipping for Item 9-7368-125
7.63 cu in PTO Drive Motor BMSY125E2SLS
Item Number: 9-7368-125
Price: $307.35
Estimate shipping to:
Shipping Notes:
* UPS 3-Day, 2-Day, and Next Day orders entered before 1pm (CST) Mon-Fri will be shipped the same day. Orders entered Sat or Sun will be shipped the following Monday.
  • This item is on page 82 of our current catalog
Description
PTO DRIVE MOTOR
Brand new, hydraulic motor with agricultural standard six tooth splined shaft. Tapered roller bearings on output shaft for high axial and radial load capacity. Shaft has retention groove centered 1-1/2" from shaft end.
Interchangeable with the following motor lines: CHAR-LYNN 2000, DANFOSS OMS/OMSS, WHITE RE/DH, PARKER-ROSS MB/TF.

SPECIFICATIONS
  • Disp. 7.63 cu. in./rev.
  • Motor Type Geroler
  • Pressure:
      2576 PSI cont.
      3091 PSI int.
  • Torque:
      2744 in-lbs. cont.
      3275 in-lbs. int.
  • Speed:
      600 RPM cont.
      720 RPM int.
  • Flow:
      19.7 GPM cont.
      23.6 GPM int.
  • Rotation Reversible
  • Mount 2 bolt SAE A
  • Shaft 1-3/8" 6T spline, 4" long
  • Rqd. Filtration 25 Micron
  • Ports SAE 10
  • Case Drain SAE 4
  • Size 7" x 5-3/16" x 4-1/16"
  • Shpg. 28 lbs.
Ask A Question
Submit a question for this product

Showing Questions of 35

Do you sell rebuild kits for this motor ?

A: Yes we do sell rebuild kits for this motor. The item number is 61591.

does the pto come in 1000 shaft splin

A: This motor does not come in 1000 shaft spline.

What are the hydraulic hook up sizes....3/8 or 1/2 inch I assume. It is my intentions to use this motor to repower a brush hog to tun on a bobcat t650. It runs 23 gpm. This appears to be the best suited motor for the application

A: SAE 10 oring fitting

What is the starting torque ability of this motor?

A: If the pressure is regulated to the continuous rated 2500 psi it would produce a total torque of 2744 in-lbs. once at that pressure. If you have any further questions please contact Product support at 1-800-488-3407, so that we may better assist you.

I have a Cat 262B skid steer loader that has a flow rate of 22GPM, and a relief pressure of 3300 PSI. I also have a WoodMaxx SB72" snow blower that currently is a 3-point hitch model that runs at 540 RPM. I would like to convert the snowblower over to use on my skidsteer. Would this motor work for that.

A: Unfortunately, that is not a question we can answer.

I have a Gehl 4835 SXT 19 gal per minute flow, I bought a Lorenz snow blower rated at 16-40 HP my pressure is 2750 psi and I have 30 H.P. hydraulic flow, this should work great for the 540 PTO speed I need I am hoping.... Thanks for any info you can give me, also can you get me the proper relieve valve to put on this also.

A: We're sorry. We are unable to assist in system design.

I have a Gehl 4835 SXT 19 gal per minute flow, I bought a Lorenz snow blower rated at 16-40 HP my pressure is 2750 psi and I have 30 H.P. hydraulic flow, this should work great for the 540 PTO speed I need I am hoping.... Thanks for any info you can give me, also can you get me the proper relieve valve to put on this also.

A: Please call our support staff at 800-488-3407 so we may better assist you.

I have a dozer that has a 20 gpm max attachment circuit at 3000psi. How much HP will this motor put out at those specs.?

A: It will produce approximately 31.6 Hp with those input values. However, because the continuous rating for the input pressure is only 2576 psi, it should not operated at the full 3000 psi for any continued period of time. If operated at that pressure it should be limited to 10% duty; or 6 seconds out of every minute at that load.

Would this motor drive a 9" post hole auger alone from the aux hydraulics of a 14 gpm skidsteer or would it need to to be attached to a gearbox to get the 3 to 1 ratio like a tractor usually uses.

A: We don't have any information about your system pressure or desired rpm to state torque and speed accurately enough to say. All we can say is that with 14 gpm this motor would turn 423 rpm, and if the pressure is regulated to the continuous rated 2500 psi it would produce a total of 18 Hp.

Would like to mount a snow blower to the front loader of my tractor. Snow blower is a 30 Hp 540 rpm pto rear mount . Would use this motor to drive the blower and a HC-P-K11C pto pump to drive the unit . Would this be a good combination or would something else work better . The tractor has both a 540 rpm pto on rear and a 2000 rpm mid mount pto. Any help in which components to use would be greatly appreciated. Also should i use 3/4 or 1 inch pressure hose. Thank You for any help.

A: Ultimately it comes down to what kind of concessions you want to make in performance. If that pump were operated at 540 rpm to drive this motor; it would turn 636 rpm (slightly over the continuous rating speed-possibly reducing lifespan). The pump is only rated for 2000 psi max, which will reduce the torque output of the motor. The overall power possible out of the motor even at that speed would then be, at best, 21.5 Hp. If you have a 30 Hp snow blower there will be an obvious deficit and noticeable reduction in capability. Please contact our Product Support with more details for further assistance.

I have a Kubota L3800DT that I want to use to power a 4' brush hog. I am going to convert the brush hog to use a hydraulic motor to turn the gear box rather than the standard PTO on the tractor. The L3800 has an advertised implement flow rate of 6.3 gpm at 2273 psi. I need approx. 20 hp and 540 rpm for the light work that I am going to do with the cutter. Can you recommend a hydraulic motor that will work for my needs? Thanks in advance for your help with this matter.

A: Unfortunately, your hydraulic output capacity is only equal to 8.35 Hp before any losses incurred by operating a hydraulic motor cuts that further. It simply doesn't seem possible with the stated values.

Would running a 3/8" hose from my skidloader to the motor increase the speed, versus the 1/2 inch hose?

A: At the same flow rate from the equipment, there would no discernible motor speed increase. The fluid speed in the hose would be faster, but that would be the only change.

i have a gehl ctl 70 skidloader that im adapting a 72 in brush cutter to my gpm on loader is 19.8 with 2988 psi would this work for what i want to do?

A: At that flow, this motor would turn 599 rpm. The system pressure will have to be regulated to the motor's continuous duty rated pressure of 2500 psi. At that flow and pressure the motor would produce about 26 Hp. If that amount of power is enough for that cutter, it could work. Check with the cutter manufacturer for minimum horsepower requirements.

I have a svl 90-2 3185 psi. 25.1 gal/min want to run a 540 pto snowblower and 540 pto stump grinder do i need two motors or will one be fine using the short shaft pto? Which motor would you prefer? Thank you

A: First research the pieces you wish to drive to discover the HP consumption. If that value is over 25 HP, this entire series of motors is not suited, even if the flow and pressure available were limited to the continuous ratings. If the HP values are in excess of the stated limit for this series, there are other options-but still must be able to meet the driving requirements when the system is limited to the rated continuous input values for any motor. Please contact our Product Support department with more information if you need further assistance.

When are you getting more in stock?

A: We are expecting shipments in January and March of 2018.

I have a jd 4020 with and advertised 18gpm @ 2250psi, would this power a rotary cutter needing 25 hp @ 540 rpm?

A: No. At those values it would produce 20.7 Hp at best.

Hi, I have a garden tractor with 30 HP and I would like to drive my sprayer which needs 7 HP with hydromotor instead of pto. Which product could you offer and can I learn the price? Thank you very much

A: We offer many products. Please contact our Product Support department with the specifications for hydraulic flow and pressure available on your unit along with what rpm you desire to turn, and it will be much easier to narrow down choices available to you, as well as their pricing.

What hose in 1/2" is needed to connect to to item 9-8745 as one has sae 10 and other sae 12 connection ports ?

A: Our hoses are either 1/2" NPT fixed male ends or JIC female swivel-to-tight ends. Adapter fittings would be required to use either.

Many Hydraulic Motors can be used as a pump too. Can this be driven so that it functions as a pump as well?

A: The manufacturer does not recommend that use for this series of motors.

I have a TM 7 harley power rake that is designed to be run with 50 hp plus tractor I have an industrial John Deere 210le skip loader that is 80 hp, the machine dose not have a pto, the hydraulic system has a flow of 25 gpm and 2750 psi, what pump will I need to operate the rake and what valves are needed

A: None of these PTO output motors will have adequate horsepower to run that piece of equipment. The most powerful one will only produce 26.1 HP continuously.

What check valve would i need to allow mower to free spin down

A: Ideally item 9-8745 would be used to provide pressure protection for the motor and a free flow loop for winding down. A double relief valve and a check valve could be installed as well, but would require a bit more plumbing.

I have a Caterpillar 287b with a hydraulic output of 22 GPM and a pressure relief of 3335psi. I too want to run a hydraulic motor on my brush hog. I understand I need a pressure relief valve to protect the motor from over pressure and also a relief valve for spool down protection. Can you give me part numbers so I can order the proper parts...Thanks...Lee

A: Item 9-8745 will serve both those functions. Idling the equipment down slightly from rated output speed will bring the output flow to the continuous operation flow rating for that motor.

Hi! Do you ship motor to Norway?

A: We do. Please contact our Customer Service department and we can work up an international quote.

I have a 2013 Caterpillar 304e excavator. I am wanting to convert a 4' PTO driven bushog to operate with a hydraulic motor powered by the excavator auxiliary hydraulics. I was looking at your 7.3 cu in splined motor. A motor with a splined shaft is preferred but not required. This motor would be connected through a slip clutch to the bushog gearbox. The motor specs indicate that the motor is rated at 600 RPM at a flow rate of 19.6 GPM. The auxiliary hydraulic on my excavator is rated at 15.9 GPM at rated engine RPM. Would this motor work for this application? Is it rugged enough for the application? Is there a motor that you sell that would be a better fit for my application? Thanks, NB

A: As long as the motor is supplied by a flow equal to or less than the stated continuous rating, and protected from the system pressure by a double relief valve if the system pressure exceeds the motor's continuous rating, it should function. It is strongly recommended that the horsepower draw of the bush hog is compared to the output of the motor under the operating system values. If it meets that requirement it seems likely that it will work. Other customers have used the motors in this series to do exactly what you describe, largely with positive results.

I am also wanting to build a system to attach a brush hog to the front of my skidsteer, My Skidsteer has a 21 GPM pump at idle. I was thinking about using the 7.63 pump which seems to be fine, I am just curious if the final RPM will be alright? Also in other post you refer to the use of hydraulic check valve to use to allow the blades to slow down gently, could you please give me a part number or item of which check valve I would need and how many I would need and maybe a general idea how to plumb them into the system. Thanks

A: past time to respond

I'm going to build a brushcutter for my skid loader . Should I mount this motor direct to the blades or mount the motor to a gearbox on the machine

A: That would depend on how many RPM the motor will turn given your input flow, and how many RPM the blades are designed for. These motors are often used to approximate PTO input speeds driving a gearbox. Please be aware of any difference between the HP required to drive the cutter mechanically, and the HP the motor will put out hydraulically.

Is the case drain required for use or can it be plugged on this model?

A: It is not necessary to use the case drain on this motor if it used individually. If used in series, the case drain should be hooked up. If hooked up during individual use, it will reduce case pressure and help internal lubrication. If hooked up in series, it will protect the case from overpressure if the downstream motor is overloaded.

Hi I have a machine with a PTO hydraulic pump that has 20gpm flow and 3000psi. I am going to convert my brush hog to run on the front of the tractor. Is this motor the correct size for this application? Also I'm confused to which valves I should get for it. A check valve, cushion valve and relief valve. I need all 3?? The hydraulic pump runs off the pto so when I turn the pto off the pump should spin down so I wouldn't need check valve? Thanks

A: We recommend a dual crossover relief valve to prevent damage if the machine hits something that stops the blades. In addition a check valve installed across the two lines to the motor will allow the motor to spin down from it's moving inertia when the pump flow is stopped.

hello, my machine has a 24.1 gpm flow rate. will i need to regulate this to avoid harming the pump? and if so what kind of valve would you recommend i could use for that. thank you

A: A flow regulator such as 9-064-75 would be good for reducing the GPM going to the motor.

My skid steer is 21 gpm at 3450psi will this work or is the pressure to high

A: Your should limit the pressure to the motor to 2576 psi continuous with an external relief valve.

my machine has a 20 gpm and 3000 psi can I run it straight to the motor or would I have to have a relief valve

A: Your machine should have a relief valve in it that would control maximum pressure. A cushion valve (crossover relief) would help if you hit something. Also consider a check valve between the lines to allow the motor to coast to a stop when the valve is turned off.

I have a bobcat with auxiliary flow of 17.1 GPM. I am trying to connect it to a brush hog. To achieve approximately 540 rpm the program tells me I need a 7.32 cu in motor. What do I use to allow the brush hog cutter to slow down by free wheeling when the hydraulics on the bobcat are turned off so it does not slam to a stop. Is this a cushion valve?

A: A cushion valve will absorb shock but not allow the spin down you are asking about. To do this a check valve can be installed in parallel to the motor between the two hydraulic lines. Then when the oil flow is stopped it still allows it to flow in a small loop until the motor stops spinning from it's inertia.

On a 9-7368-125 hydraulic motor, how do you tell the Inlet from the Outlet?

A: These motors are bidirectional, so each port can be inlet or outlet. As you face the shaft of the motor, using the right hand port that is staggered forward as the inlet and the rear port staggered backward as the outlet, the shaft should turn clockwise. Reversing the flow will reverse the motor.

I have a 773G Bobcat a looking to hyd drive a single stage snow blower pto motor ????? thinking 7.63ci ???? or ??? It has 24" blower seen them on 25-30hp tractors 540rpm 773G= 16.5GPM - - Pressure ??? will it work?

A: With your flow rate you will have about 500 RPM from the motor. At continuous pressure rating of 2576 PSI this equates to between 21 and 22 HP.

i have a skid steer with 11 gpm pump will this motor run a auger

A: Yes it would subject to the diameter and length of the auger. Speed will be about 300 RPM. Torque is dependent on what pressure your system operates with. If you need more RPM you could choose a smaller displacement motor, however this will reduce the torque output.

Recently Viewed
Email a Friend
7.63 cu in PTO Drive Motor BMSY125E2SLS
Item Number: 9-7368-125
Price: $307.35
Message for your friend:

I found this on the Surplus Center website, https://www.surpluscenter.com/. I thought you might be interested in seeing it for yourself. Please click on the following link to view the page:

7.63 cu in PTO Drive Motor BMSY125E2SLS
Additional Comments:

Please wait...
Newsletter SignUp