0.49 cu in Dynamic GPF1080PC Hydraulic Pump

Item Number: 9-7769-B

Price: $108.55
Back to top

0.49 cu in Dynamic GPF1080PC Hydraulic Pump

0.49 cu in Dynamic GPF1080PC Hydraulic Pump

item number: 9-7769-B PRICE: $108.55 4 In Stock Regular Stock Item

Available for curbside pickup in our Lincoln, NE location
calculate shipping
Calculate Shipping for Item 9-7769-B
0.49 cu in Dynamic GPF1080PC Hydraulic Pump
Item Number: 9-7769-B
Price: $108.55
Estimate shipping to:
Shipping Notes:
* UPS 3-Day, 2-Day, and Next Day orders entered before 1pm (CST) Mon-Fri will be shipped the same day. Orders entered Sat or Sun will be shipped the following Monday.
  • This item is on page 42 of our current catalog
Brand new, DYNAMIC GP-F10 series hydraulic gear pump. Aluminum center section with cast iron end covers.

  • Disp. 0.49 cu. in. / rev.
  • Pump Type Gear
  • Rotation CW
  • Pressure:
      2900 PSI rated
      3480 PSI peak
  • Speed:
      2000 RPM rated
      4000 RPM max.
  • Flow:
      3.95 GPM rated
      7.89 GPM max.
  • Mount 2 bolt SAE AA
  • Shaft 1/2" dia. x 1-1/16" long with 1/8" wide keyway
  • Rqd. Filtration 25 micron
  • Inlet Port SAE 8
  • Outlet Port SAE 6
  • Size 4" x 4-1/32" x 3-5/16"
  • Shpg. 7 lbs.
Ask A Question
Submit a question for this product

Showing Questions of 6

will this pump work a scissor lift with gas motor

A: If the system were designed correctly it very likely could. Customers have used this series of pumps in applications much like that in the past.

Can I run this on a 8hp gas engine, 3x16 cylinders

A: At 3600 rpm and 3000 psi, this pump will consume approximately 21 HP. With only 8.5 HP, you could expect to develop about 1200 psi continuously without killing the engine.

Can these pumps be mounted horizontal and vertical as in shaft up and shaft down?

A: They can be mounted and operated in any orientation, as long as it is direct driven. These pumps do not tolerate side load.

Will this Pump, service 2 cylinders (2.5 inch bore with 1.25 shafts), on a small FEL...

A: It would. Any pump would work, just the speed would be different.

Do you have any operation, maintenance or troubleshooting information for this 1080 pump??

A: There are no manuals provided for these pumps. Basic hydraulic maintenance, troubleshooting and operating principles apply. Avoid cavitation and try to keep a flooded inlet. Make sure you have enough fluid for the system (approx 1 gallon for every gallon per minute pumped) and keep the fluid clean using a return filter. Turn the pump the correct rotation, (called out as you face the shaft) at or under the stated maximum. Avoid side load on the drive shaft with this series. Set the relief for the system at or below the stated maximum.

Does this pump have a bearing on the output shaft so it can be pulley driven? Can the output shaft take side loading pressure?

A: There is not a bearing on the shaft. It is designed for direct drive only. If if must be belt driven you should use a jack shaft with the pulley mounted between two bearings and the shaft directly coupled to the pump.

Recently Viewed
Email a Friend
0.49 cu in Dynamic GPF1080PC Hydraulic Pump
Item Number: 9-7769-B
Price: $108.55
Message for your friend:

I found this on the Surplus Center website, https://www.surpluscenter.com/. I thought you might be interested in seeing it for yourself. Please click on the following link to view the page:

0.49 cu in Dynamic GPF1080PC Hydraulic Pump
Additional Comments:

Please wait...
Newsletter SignUp