40 HP Omni Gear RC-30 Rotary Cutter Gearbox1:1.93 Ratio Model 250045

Name: 40 HP Omni Gear RC-30 Rotary Cutter Gearbox1:1.93 Ratio Model 250045
Brand: Omni Gear
Price: 178.30 USD
Availability: InStock

Item Number: 13-1528

Price: $178.30

TOP

Description
More Specs
Ask A Question
Recently Viewed

Home
Power Transmission
Gear Reducers & Gearboxes
Rotary Cutter Gearboxes
40 HP Omni Gear RC-30 Rotary Cutter Gearbox1:1.93 Ratio Model 250045

40 HP Omni Gear RC-30 Rotary Cutter Gearbox1:1.93 Ratio Model 250045

✓Add to Wishlist

calculate shipping

This item is on page 195 of our current catalog

print page

You may also consider:

Replacement Omni Gear Blade Hub RC-30 210000 210000 $33.30

Description
More Specs
Ask A Question
Recently Viewed

Description

DESCRIPTION

1:1.93 SPEED INCREASER

Brand new, OMNI GEAR series RC-30 right angle rotary cutter gearbox. Horizontal input and vertical output downward. Bevel gears. Large deep groove ball bearings to support output. Four 5/16"-18 tapped holes on 3-5/16" dia. B.C. Ships without oil, user must add oil prior to use per user ‘s manual.

SPECIFICATIONS

Model 250045
Rotation CCW input gives CW output
Gear Ratio 1:1.93 Increaser
Input RPM 540/1000
Output RPM 1042/1930
Input HP 24-40
Max Torque 2800-4667 in.lbs.
Input Shaft 1-3/8" dia. x 3" long W/ 1/2" dia. pinhole
Output Shaft 1-9/16" dia. 12 tooth tapered spline w/threaded end. 4-1/2" total length
Blade Hub 2.95" dia. x 2.02" stepped down to 2.5" dia. x 0.27" then tapers down to 2.183" dia. over 0.315"
Mount 4 holes on 6.8" dia. B.C.
Pilot 5-1/4" dia.
Size 10-1/4" x 7" x 7"
Shpg. 54 lbs.

More Specs

MORE SPECS

Click on boxes below for more information about this product.

Dimensional Diagram

User's Manual

Ask A Question

ASK A QUESTION

Submit a question for this product

Showing Questions of 8

What is the location of the oil drain plug and should the oil be drained when hot?

A: Draining while heated would likely be easier, however there is no drain port.
Date Submitted: 09/20/2020

I need to know what Gear box I need for a County line 60 inch mowing deck the PTO part number is QMC 752M RATIO 1:1.93 the mower deck is Tarter industries Serial 001752 it looks like the sku is C4-3617824 2

A: Unfortunately, we have no cross reference material for that equipment and no access to specifications to state which one of our products may be close enough to what you have. Please contact our Product Support department with measurements and further details.
Date Submitted: 07/23/2018

How to remove output gear from housing and replace snap rings?

A: That question may be better answered by the Technical department at Omni. Their contact information is readily available online.
Date Submitted: 05/03/2017

These are currently unavailable here. Do you ship to Brisbane Australia and how much would that be?

A: Please email our Customer Service department with your shipping information, and they can work up an international quote for you. customerservice@surpluscenter.com
Date Submitted: 03/09/2017

Can gear box be ran on its side so the output shaft is horizontal instead of vertical?

A: If the venting was routed so it didn't leak, and the orientation still provided proper lubrication, it could be possible.
Date Submitted: 12/16/2016

I have a unknown brand gear box only numbers I can make out on tag are 60202 2 5004 5, Is there anyway you can match that number? Thanks

A: We have no way to cross reference that number to find a replacement.
Date Submitted: 10/07/2016

The picture of the gearbox shows a protector on the output shaft splines. Is this protector machined with internal splines and can it be welded in a hub?

A: This gearbox does come with a blade hub that is internally splined, machinable and weldable.
Date Submitted: 09/26/2016

Is this gearbox fit a 5 foot king-kutter.

A: They look similar, but it would depend on the ratio and horsepower for your unit. We have no specifications for that manufacturer beyond what is available in the internet. It will be up to you to do the research to make sure it is the correct unit.
Date Submitted: 05/23/2016

You may also consider:

Replacement Omni Gear Blade Hub RC-30 210000 210000 $33.30

40 HP Omni Gear RC-30 Rotary Cutter Gearbox1:1.93 Ratio Model 250045

Item Number: 13-1528

40 HP Omni Gear RC-30 Rotary Cutter Gearbox1:1.93 Ratio Model 250045

40 HP Omni Gear RC-30 Rotary Cutter Gearbox1:1.93 Ratio Model 250045

You may also consider:

Showing Questions of 8

What is the location of the oil drain plug and should the oil be drained when hot?

A: Draining while heated would likely be easier, however there is no drain port.Date Submitted: 09/20/2020

I need to know what Gear box I need for a County line 60 inch mowing deck the PTO part number is QMC 752M RATIO 1:1.93 the mower deck is Tarter industries Serial 001752 it looks like the sku is C4-3617824 2

A: Unfortunately, we have no cross reference material for that equipment and no access to specifications to state which one of our products may be close enough to what you have. Please contact our Product Support department with measurements and further details.Date Submitted: 07/23/2018

How to remove output gear from housing and replace snap rings?

A: That question may be better answered by the Technical department at Omni. Their contact information is readily available online.Date Submitted: 05/03/2017

These are currently unavailable here. Do you ship to Brisbane Australia and how much would that be?

A: Please email our Customer Service department with your shipping information, and they can work up an international quote for you. customerservice@surpluscenter.comDate Submitted: 03/09/2017

Can gear box be ran on its side so the output shaft is horizontal instead of vertical?

A: If the venting was routed so it didn't leak, and the orientation still provided proper lubrication, it could be possible.Date Submitted: 12/16/2016

I have a unknown brand gear box only numbers I can make out on tag are 60202 2 5004 5, Is there anyway you can match that number? Thanks

A: We have no way to cross reference that number to find a replacement.Date Submitted: 10/07/2016

The picture of the gearbox shows a protector on the output shaft splines. Is this protector machined with internal splines and can it be welded in a hub?

A: This gearbox does come with a blade hub that is internally splined, machinable and weldable.Date Submitted: 09/26/2016

Is this gearbox fit a 5 foot king-kutter.

A: They look similar, but it would depend on the ratio and horsepower for your unit. We have no specifications for that manufacturer beyond what is available in the internet. It will be up to you to do the research to make sure it is the correct unit.Date Submitted: 05/23/2016

40 HP Omni Gear RC-30 Rotary Cutter Gearbox1:1.93 Ratio Model 250045

You may also consider:

A: Draining while heated would likely be easier, however there is no drain port.
Date Submitted: 09/20/2020

A: Unfortunately, we have no cross reference material for that equipment and no access to specifications to state which one of our products may be close enough to what you have. Please contact our Product Support department with measurements and further details.
Date Submitted: 07/23/2018

A: That question may be better answered by the Technical department at Omni. Their contact information is readily available online.
Date Submitted: 05/03/2017

A: Please email our Customer Service department with your shipping information, and they can work up an international quote for you. customerservice@surpluscenter.com
Date Submitted: 03/09/2017

A: If the venting was routed so it didn't leak, and the orientation still provided proper lubrication, it could be possible.
Date Submitted: 12/16/2016

A: We have no way to cross reference that number to find a replacement.
Date Submitted: 10/07/2016

A: This gearbox does come with a blade hub that is internally splined, machinable and weldable.
Date Submitted: 09/26/2016

A: They look similar, but it would depend on the ratio and horsepower for your unit. We have no specifications for that manufacturer beyond what is available in the internet. It will be up to you to do the research to make sure it is the correct unit.
Date Submitted: 05/23/2016