1" 15T Splined Coupling G & G Mfg 163-1615

Item Number: 1-1561

Price: $9.25

Description
Ask A Question
Recently Viewed

Home
Power Transmission
Shaft Couplers
Keyed, Splined & Hex 1 Piece Solid Couplers
1" 15T Splined Coupling G & G Mfg 163-1615

1" 15T Splined Coupling G & G Mfg 163-1615

calculate shipping

This item is on page 137 of our current catalog

print page

Description
Ask A Question
Recently Viewed

Spline Shaft Coupler
Brand new spline shaft coupler for hydraulic pumps, gearboxes, etc.

SPECIFICATIONS

Made from cold rolled steel
Machinable and weldable
1" 15 Tooth spline
1-1/2" OD x 2-1/4"
Shpg 1 lbs

Ask A Question

ASK A QUESTION

1" 15T Splined Coupling G & G Mfg 163-1615

Item Number: 1-1561

1" 15T Splined Coupling G & G Mfg 163-1615

1" 15T Splined Coupling G & G Mfg 163-1615

Showing Questions of 13

For this and other couplers, do the splines run continuous without a center rib? I need one to slide on a shaft for intermittent engagement of two shafts.

A: The spline does run continuous through the coupler. We do not have any that are splined halfway.Date Submitted: 04/09/2019

will this also fit the following 2.81 cu in Rexroth AA10VG45DGD2/10R-NSC60F015S Piston Pump

A: If you are referring to item # 9-8558; then yes. The pump shaft is 1" 15 tooth. So is this coupler.Date Submitted: 12/23/2018

Are these made from 1018 cold rolled steel? Thanks

A: The grade of steel in not specified in the manufacturer literature. All that is stated is that it is machinable, weldable, cold rolled steel and that low hydrogen electrodes are recommended for welding on these pieces.Date Submitted: 12/14/2018

Do you ship this to The Netherlands ?

A: We do ship worldwide. Please contact our Product Support department with your order and shipping details and we can provide an international quote.Date Submitted: 11/19/2018

Does this fit a mid mount 2000 rpm pto shaft

A: Frequently mid-mount PTO shafts are 1" 15 tooth, yes. It would be best to double check the shaft in question.Date Submitted: 10/13/2018

Is this bushing concentric between spline bore and outside diameter? Do you know what this tolerance is?

A: We do not have the engineering data to confirm with any greater detail than we already have. This product is manufactured by G & G Manufacturing in Omaha, Nebraska as part number 163-1615. They may have dimensional prints with the stated tolerances you seek.Date Submitted: 07/21/2018

Is the OD concentric with ID?

A: Yes. The o.d. of the coupler is 1.499". The i.d. of the coupler at the valley of the female spline is 1.020" for use with 1" o.d. male spline. The i.d. of the coupler's meshing male teeth is 0.889". All diameters are concentric.Date Submitted: 07/16/2018

hi do you have this product in 1 1/4 inch with 16 spline please.

A: No, we only have 1-1/4 14 tooth spline.Date Submitted: 08/17/2017

Will you ship this item to Ireland? Having difficulty getting this at a reasonable price this side of the Atlantic Thanks.

A: We ship worldwide. Please contact our Customer Service Department with your information and they can get you an international quote.Date Submitted: 04/08/2017

Does this coupling fit item #1-3092-6 ?

A: Yes, they are the same spline.Date Submitted: 09/03/2016

Does this coupling have set screws for attaching to shaft?

A: No, this coupling does not have set screws.Date Submitted: 08/24/2016

Do you have matching fully splined shaft for this coupler

A: No we don't have an 1" 15 tooth splined shafting.Date Submitted: 11/23/2015

Do you have the 1" 15t splined coupling in 6" long ? If you do what is the # and cost? Thank you Tom.

A: This item is the only coupling we have for the 1" 15 tooth spline. One possibility would be to use item 1-3090, cut to your desired length with a 1-1561 at each end.Date Submitted: 02/14/2014

1" 15T Splined Coupling G & G Mfg 163-1615

A: The spline does run continuous through the coupler. We do not have any that are splined halfway.
Date Submitted: 04/09/2019

A: If you are referring to item # 9-8558; then yes. The pump shaft is 1" 15 tooth. So is this coupler.
Date Submitted: 12/23/2018

A: The grade of steel in not specified in the manufacturer literature. All that is stated is that it is machinable, weldable, cold rolled steel and that low hydrogen electrodes are recommended for welding on these pieces.
Date Submitted: 12/14/2018

A: We do ship worldwide. Please contact our Product Support department with your order and shipping details and we can provide an international quote.
Date Submitted: 11/19/2018

A: Frequently mid-mount PTO shafts are 1" 15 tooth, yes. It would be best to double check the shaft in question.
Date Submitted: 10/13/2018

A: We do not have the engineering data to confirm with any greater detail than we already have. This product is manufactured by G & G Manufacturing in Omaha, Nebraska as part number 163-1615. They may have dimensional prints with the stated tolerances you seek.
Date Submitted: 07/21/2018

A: Yes. The o.d. of the coupler is 1.499". The i.d. of the coupler at the valley of the female spline is 1.020" for use with 1" o.d. male spline. The i.d. of the coupler's meshing male teeth is 0.889". All diameters are concentric.
Date Submitted: 07/16/2018

A: No, we only have 1-1/4 14 tooth spline.
Date Submitted: 08/17/2017

A: We ship worldwide. Please contact our Customer Service Department with your information and they can get you an international quote.
Date Submitted: 04/08/2017

A: Yes, they are the same spline.
Date Submitted: 09/03/2016

A: No, this coupling does not have set screws.
Date Submitted: 08/24/2016

A: No we don't have an 1" 15 tooth splined shafting.
Date Submitted: 11/23/2015

A: This item is the only coupling we have for the 1" 15 tooth spline. One possibility would be to use item 1-3090, cut to your desired length with a 1-1561 at each end.
Date Submitted: 02/14/2014